alarm01

Alarm 01: S-arm clamp detection OFF

alarm02

Alarm 02:Product hold 1 detection OFF

alarm03

Alarm 03: Product hold 2 detection OFF

alarm04

Alarm 05: Product hold 4 detection OFF

alarm05

Alarm 05: Product hold 4 detection OFF

alarm06

Alarm 06: Product suction 1 detection OFF

alarm07

Alarm 07:Product suction 2 detection OFF

alarm076

Alarm 76: Program running, waiting for X26 signal for too long

alarm078

Alarm 78: (X07) is not OFF

alarm08

Alarm 08:Product suction 3 detection OFF

alarm09

Alarm 09: Product suction 4 detection OFF

alarm10

Alarm 10: Mould open (x46) is not OFF

alarm11

Alarm 11: Mould close X45 ON mould open X46 ON

alarm12

Alarm 12: Injection machine mould open fault

alarm13

Alarm 13: Posture and aligning signal fault

alarm14

Alarm 14: Lateral posture cylinder is abnormal

alarm15

Alarm 15:S-arm rising limit(X07) is not ON

alarm16

Alarm 16: S-arm rising limit(X07) is not OFF

alarm17

Alarm 17: posture cylinder sensor Flashover

alarm18

Alarm 18: Rotating action is abnormal

alarm19

Alarm 19: Rotating cylinder origin and complete signal ON

alarm199

Abnormal limit switch

alarm20

Alarm 20: Air pressure is low

alarm200

Alarm 200: Abnormal setting

alarm21

Alarm 21: Rotating cylinder group sensor is OFF

alarm22

Alarm 22: The action program is abnormal

alarm23

Alarm 23: The action program is abnormal

alarm24

Alarm 24: The action program is abnormal

alarm25

Alarm 25: IMM auto-signal is abnormal

alarm26

Alarm 26: Found no mould open over signal

alarm27

Alarm 27: Secondary arm's retreat limit(X32) is not ON

alarm28

Alarm 28:S-arm forward limit is not ON

alarm29

Alarm 29: Mid-plate signal is not ON

alarm30

Alarm 30: The ejector forward signal fault

alarm31

Alarm 31: Stub bar detection is not OFF

alarm32

Alarm 32: Product hold 1 Cfm is not OFF

alarm33

Alarm 33: Product hold 2 Cfm is not OFF

alarm34

Alarm 34: Product hold 3 Cfm is not OFF

alarm35

Alarm 35: Product hold 4 Cfm is not OFF

alarm36

Alarm 36: Product suction 1 Cfm is not OFF

alarm37

Alarm 37: Product suction 2 Cfm is not OFF

alarm38

Alarm 38:Product suction 3 Cfm is not OFF

alarm39

Alarm 39: Product suction 4 Cfm is not OFF

alarm40

Alarm 40: mould unloading over is not OFF

alarm41

Alarm 41: mould unloading（X46）is OFF

alarm42

Alarm 42: Outside the safety zone

alarm43

Alarm 43: Mould open/close signal is abnormal

alarm44

Alarm 44: Mould zone safety signal is abnormal

alarm45

Alarm 45: Moulding machine signal is abnormal

alarm46

Alarm 46: mid- plate signal is missing

alarm47

Alarm 47: Inside posture abnormal

alarm48

Alarm 48: Mould outside standby abnormal

alarm49

Alarm 49: M-arm is outside the safety zone

alarm50

Alarm 50: S-arm is outside the safety zone

alarm51

Alarm 51: Action zone is abnormal (Z axis)

alarm52

Alarm 52: T/O action zone is abnormal(X axis)

alarm53

Alarm 53: Placement action zone is abnormal(X axis)

alarm54

Alarm 54: T/O action zone is abnormal(R axis)

alarm55

Alarm 55: Placement action zone is abnormal(R axis)

alarm56

Alarm 56: T/O action zone is abnormal(Y axis)

alarm57

Alarm 57: Placement action zone is abnormal(Y axis)

alarm58

Alarm 58: T/O action zone is abnormal(YS axis)

alarm59

Alarm 59: Placement action zone is abnormal(YS axis)

alarm60

Alarm 60: Decline standby zone is abnormal(Y axis)

alarm61

Alarm 61: Decline standby zone is abnormal (YS axis)

alarm62

Alarm 62: Take-out/placement zone signal are abnormal

alarm63

Alarm 63: #001 program instruction is wrong

alarm64

Alarm 64: Z axis sense the maximum limit

alarm65

Alarm 65: X axis sense the maximum limit

alarm66

Alarm 66: Y axis sense the maximum limit

alarm67

Alarm 67: R axis sense the maximum limit

alarm68

Alarm 68: YS axis sense the maximum limit

alarm69

Alarm 69: [Std-Pro] mode is not selected

alarm70

Alarm 70: [Std-Pro] mode select is error

alarm71

Alarm 71: [S-arm cylinder] type is not selected

alarm72

Alarm 72: Program running, waiting for X21 signal for too long

alarm73

Alarm 73: Program running, waiting for X29 signal for too long

alarm74

Alarm 74: Program running, waiting for X22 signal for too long

alarm75

Alarm 75:Program running, waiting for X14 signal for too long

alarm77

Alarm 77:Program running, waiting for X19 signal for too long

alarm79

Alarm 79:(X20) is not OFF

alarm80

Alarm 80: Axis interference

alarm81

Alarm 81: Posture prohibited

alarm82

Alarm 82: Posture prohibited

alarm83

Alarm 83: Posture prohibited

alarm84

Alarm 84:Ear Rubbing Cylinder A limit(I10) is not ON

alarm85

Alarm 85:Ear Rubbing Cylinder B limit(I11) is not ON

alarm86

Alarm 86:Assemble Upper Cylinders (OFF) limit(I12) is not ON

alarm87

Alarm 87 :Assemble Upper Cylinders (ON) limit(I13) is not ON

alarm88

Alarm 88 :Fixed Cylinder(OFF) limit(I14) is not ON

alarm89

Alarm 89 : Fixed Cylinder(ON) limit(I15) is not ON

alarm90

Alarm 90 :Ear Cylinders1(OFF) limit(I16) is not ON

alarm91

Alarm 91 :Ear Cylinders1(ON) limit(I17) is not ON

axisalarm01

Axis alarm 01: ROM/RAM error

axisalarm02

Axis alarm 02: TS-LINK Communication error

axisalarm04

Axis alarm 04: Abnormal encoder input

systemalarm04

System alarm 04:Operating data error. Find abnormal system data

systemalarm06

System alarm 06: Abnormal backup RAM

systemalarm07

System alarm 07: Abnormal program controller system

systemalarm08

System alarm 08: Lithium battery is insufficient.

systemalarm13

System alarm 13: Abnormal motion board RAM

systemalarm14

System alarm 14: TS-LINK Communication error

systemalarm15

System alarm 15: Program controller backup RAM error

systemalarm17

System alarm 17 Directory data flash ROM errors

systemalarm19

System alarm 19: Backup data error

systemalarm20

System alarm 20: Communication error

SWITEK 2 Cavities 3L Pails Side Entry IML Solutions

20L Paint Bucket Side Entry IML Solutions.

4 Cavities buckets side entry IML Solutions

6 Cavities Yoghurt cups side entry IML Solutions with Camera

6 Cavities yoghurt cups side entry IML Solutions.